Product description
An advanced quality Two-Pack and Solvent-Free Epoxy Resin; distinguished by its reinforced formulation with specially selected hardener, fillers, and aggregates designed to offer an outstanding strong and impermeable rendering; unaffected by mechanical damage and chemical attack.
Special features
☐ Excellent adhesion characteristics. ☐ Durable and abrasion resistant coat. ☐ Rapid strength gain. ☐ Impermeable to water and liquids upon curing. ☐ Can be used for hygenic uses / purposes. ☐ High mechanical strength. ☐ Unaffected by a wide range of Acids, Alkalies and Industrial Chemicals / Detergents.
Where to use
As a protective patch repair coat / rendering over Internal & External (Vertical / Horizontal) surfaces as required i.e., ☐ Damaged Concrete Floors ☐ Broken Kerbs, Panels and Piers ☐ Levelling worn, eroded or pitted Steel & Concrete substrates ☐ Intended for general patch repair works.
Product data
FINISH : MATT COLOUR OF COMPONENTS : White : Part (A) , Black : Part (B) COLOUR OF MIXTURE : Grey VOLUME SOLID : 100% PRODUCT WEIGHT : 1.5 Kg Part (A) 1.5 Kg Part (B) REC. FILM THICKNESS : Up to 50 mm per application THEO. COVERAGE : 3 kg/m² to give 2mm layer thickness Practical coverage depends upon application thickness .surface nature and skill of applicator MIXING RATIO : Part (A) : Part (B) 1 : 1 (by volume or weight) POT LIFE : Ambient Temperature 10 °C 25 °C 45 °C 50 °F 77 °F 113 °F No. of Hours 45 min. 30 min. 15 min. FLASH POINT : Non-flammable (Solvent Free Material) COMPRESSIVE STRENGTH : 60 N/mm² (upon full curing)
Drying times
SUBSTRATE TEMPERATURE | INITIAL CURING | FULL CURING | OVERCOATING INTERVALS MINIMUM | MAXIMUM 10 °C (50 °F) | 10 hrs. | 10 Days | 12 hrs. | IND. 25 °C (77 °F) | 6 hrs. | 1 Week | 8 hrs. | IND. 40 °C (104 °F) | 2 hrs. | 4 Days | 3 hrs. | IND.
Surface preparation
1. Degrease metal surfaces in accordance with SSPC-SP1 Solvent Cleaning (Use GTC002 Thinner) to remove grease, oil, soil, dirt and other surface contamination where exist. 2. Millscale should be abrasive blasted in accordance with SSPC-SP10 (SA2½ Swedish Standard). 3. Other surfaces should be dry, clean and contamination free. (Concrete floors must be sand and loose particles free; providing a sound substrate). 4. Paint layers should be removed to extend good adhesion characteristics.
Application details
☐ USAGE: Intended for a single or more patch/layer coat applications over well prepared surfaces/ substrates.
Mixing and thinning
☐ Mix properly, appropriate and measured equal quantity as per provided pack sizes: {1.5 Kg. Part (A): 1.5 Kg Part (B) } ☐ Mixture should provide a homogeneous Grey colour. ☐ Thinning is not recommended / required. (Solvent-Free Material). ☐ METHOD OF APPLICATION: Mixed material should be applied to suitably primed surfaces with wood float.
Important restrictions
☐ For minimal wastage, mix estimated quantities which can be used / applied within 20 minutes. ☐ For a second layer coat application, allow a minimum of 6 hours interval. ☐ GTC Epoxy Putty can be applied over suitably primed/sealed surfaces i.e., Getoxy Clear Sealer (Concrete Surfaces) Getathane Clear Coating (Wooden Surfaces) Getoxy Iron Oxide Epoxy (Steel Surfaces)
Cleaning tools
Uncured Epoxy Putty can be cleaned with GTC099 Thinner immediately after use.
Application conditions
At a temperature ranging 5°C (41°F) to 40°C (104 °F) . Relative humidity is below 75%.
Storage and handling
Product must be stored as per local regulations and should be kept in dry well ventilated location far from heat and direct sunlight. Can should be tightly closed after use. Mix well before use. Storage temperature range between 5°C (41°F) to 40°C (104 °F).
Standards and approvals
Supportive information is available upon request to establish an assessment to be acquired as with regards to product's compliance with/to a particular authority's queries / specifications. Please consult with GTC Technical Service Dept.
Safety precautions
The following notes should be considered when using/applying material;- (a) Take precautions to prevent material entering the eyes (goggles should be worn, irrigate the eyes with water when become contaminated and obtain medical care at once). (b) Take precautions to avoid skin contact (gloves should be worn, barrier cream should be used). (c) Ensure that repeated contact of paint with skin is avoided. (d) Provide adequate ventilation. (Face masks must be worn). (e) Keep away from sparks and open flame (for Solvent-based materials).
Pack sizes
• 1½ kg (Part A) • 1½ kg (Part B)