Product description
Epoxy Floor Clear Coating is a high build two component solvent free Cyclo Alphatic Amine cured epoxy coating, which provides seamless smooth hard wearing durable coating with excellent chemical and abrasion resistance.
Special features
93 Durable with excellent abrasion resistance. 93 Resistant to aromatic and hydro-carbon solvent, fuels, industrial detergents and a wide range of industrial chemicals. 93 Solvent free odorless during application. 93 Dust proof, easy to clean due to its seamless smooth finish. 93 Slip resistant when spreading silica sand on top of it while yet to achieve the required texture. 93 Excellent adhesion to primed metal, concrete and sand cement plaster surfaces.
Where to use
Epoxy floor coating is suitable for most industrial plants, warehouses, parking areas and wet flooring areas such as kitchens, bathrooms, and swimming pool paths.
Product data
FINISH : Glossy COLOUR : Clear VOLUME SOLIDS : 100 % PRODUCT WEIGHT : 1.1 kg./ltr. DRY FILM THICKNESS : For floors: 150 microns per coat (approx. 6 mils). THEO. COVERAGE : For floors: 4 m2/ltr. Practical coverage primarily depends upon nature of surface profile, method of application and site conditions .MIXING RATIO : Base : Curing Agent 9.15 : 5.85 (by volume)
Important restrictions
Use for mixing a heavy duty slow sped drill fitted with proper size paddle for : 93 Minimum: 3 minutes 93 Maximum: 5 minutes POT LIFE : Ambient Temperature 25 °C 45 °C 77 °F 113 °F No. of Hours 40 min. 20 min. FLASH POINT : Not Applicable (Solvent free).
Drying times
Substrate Initial Light Fully Cure Over-coating Intervals Temperature Cure Traffic Time Minimum Maximum Time 25 °C (77 °F) 24 hrs. 48 hrs. 7 days 12 hrs. 36 hrs. 40 °C (104 °F) 19 hrs. 24 hrs. 5 days 5 hrs. 24 hrs.
Surface preparation
1. degrease areas where grease, oil and other surface contamination exist in accordance with SSPC-SP1 Solvent Cleaning. (Use GTC002 Thinner). 2. Wire Brush/Mechanical Power Tool Clean areas where laitance, surface porosity and loosely adhering foreign material exist in accordance with SSPC-SP2 and/or SSPC-SP3 Standards. 3. Steel should be abrasive blast cleaned in accordance with SSPC-SP10 Standard (SA1/2 Swedish Standard) and suitably primed as per individual situation depending upon type of substrate. Please consult with GTC Technical Service Dept. 4. Surfaces to be coated must be dry, clean and contamination free prior to paint application process. 1. Concrete damaged areas should be treated and leveled with GTC Epoxy Putty and/or GTC Epoxy Mortar Getamoor.
Where to use
1. Intended for two coat application over well prepared and suitably primed concrete and a variety of other surfaces. 2. Priming Priming needed only in a necessary cases, where concrete shows not sound and high porous bad quality, use GTC Getoxy GES Clear Epoxy Sealer to prime the required areas. 3. Anti slip application If a slip resistant texture is required, the first coat shall be applied minimum 250 microns DFT and directly blinded with the recommended GTC Silica Anti slip Grain to achieve the required texture finish. Excess aggregate should be brushed out before applying the top final coat.
Important restrictions
1. Concrete floors should be minimum 28 days old. 2. For maximum performance, curing temperatures should be above 10 °C (50 °F) since material will not adequately cure below 5 °C (41 °F). 3. Two pack epoxies are commonly known to chalk upon external exposure. 4. It is not recommended to apply two pack epoxy material over 50 °C (122 °F).
Cleaning tools
For cleaning tools and equipments use GTC099 Thinner.
Application conditions
At a temperature ranging 5°C (41°F) to 40°C (104 °F). Relative humidity is below 75%.
Storage and handling
Product must be stored as per local regulations and should be kept in dry well ventilated location far from heat and direct sunlight. Can should be tightly closed after use. Mix well before use. Storage temperature range between 5°C (41°F) to 40°C (104 °F).
Safety precautions
The following notes should be considered when using/applying painting material:- (a) Take precautions to prevent material entering the eyes (goggles should be worn, irrigate the eyes with water when become contaminated and obtain medical care at once). (b) Take precautions to avoid skin contact (gloves should be worn, barrier cream should be used). (c) Ensure that repeated contact of paint with skin is avoided. (d) Provide adequate ventilation. (Face masks must be worn). (e) Keep away from sparks and open flames (for solvent-based materials).
Pack sizes
White :- • 3 Ltr Tins (Base + Curing Agent) • 15 Ltr Tins (Base + Curing Agent)