Product description
A two-pack distinctive quality and Solvent-Free Epoxy Putty Material formulated to meet the demand on high quality putty / filler to suit specific applications of Building and Industrial requirements in the modern and advanced construction works.
Special features
[ ] Tough and abrasion resistant coat. [ ] Resistant to severe climatic conditions. [ ] Excellent adhesion characteristics. [ ] Applicable over a very wide range of substrates. [ ] Compatible with a very wide range of conventional and two-pack finishes / top coats. [ ] Provides a smooth finish. [ ] Designed for Internal and External use. [ ] Treats surface imperfections i.e., pits in steel plates & structures.
Where to use
As a protective and levelling putty material over a diversified range of Internal/External substrates including, Steel, Concrete, Masonry, Metals, Plastered Surfaces, Stone, Bricks ... etc., i.e., [ ] Steel & Concrete Walls / Superstructures [ ] Steel Plates, Beams and Structure in Refineries & Power Stations. [ ] Concrete Floors (Light & Heavy Traffic). [ ] Exterior Masonry & Building [ ] Metal Works
Product data
FINISH : MATT COLOUR : White : Part (A) , Yellow : Part (B) Can be provided in other light colours upon request (Pastel Shades). VOLUME SOLID : 100% PRODUCT WEIGHT : 1.57 kg Part (A) 1.48 kg Part (B) REC. FILM THICKNESS : Up to 5 mm per coat / application THEO. COVERAGE : approx. 2.0 m²/kg. depending upon applied thickness. Practical coverage primarily depends on nature/degree of surface porosity, method of application and site conditions. MIXING RATIO : Part (A) : Part (B) 1 : 1 (by volume or weight) POT LIFE : Ambient Temperature | 10 °C | 25 °C | 40 °C -----------------+--------+--------+------- | 50 °F | 77 °F | 104 °F No. of Hours | 45 min.| 30 min.| 15 min. FLASH POINT : Non-flammable (Solvent-Free Material)
Drying times
SUBSTRATE TEMPERATURE | INITIAL CURING | FULL CURING | OVERCOATING INTERVALS | | | MINIMUM | MAXIMUM ---------------------+----------------+-------------+----------+--------- 10 °C (50 °F) | 10 hrs. | 10 Days | 36 hrs. | IND. 25 °C (77 °F) | 6 hrs. | 1 Week | 24 hrs. | IND. 40 °C (104 °F) | 4 hrs. | 4 Days | 18 hrs. | IND.
Standards and approvals
Supportive information is available upon request to establish an assessment to be acquired as with regards to product's compliance with/to a particular authority's queries /specifications. Please consult with GTC Technical Service Dept.
Surface preparation
1. Degrease metal surfaces in accordance with SSPC-SP1 Solvent Cleaning (Use GTC002 Thinner). to remove grease, oil, soil, dirt and other surface contamination where exist. 2. Millscale should be abrasive blasted in accordance with SSPC-SP10 Standard (SA½ Swedish Standard). 3. Other surfaces should be dry, clean and contamination free. (Concrete floors must be sanded and loose free particles; providing a sound substrate). 4. Paint layers should be removed to extend good adhesion characteristics.
Application details
[ ] USAGE: Intended for a single or more layer coat applications over well prepared surfaces / substrates.
Mixing and thinning
[ ] Mix properly, appropriate and measured equal quantity as per provided pack sizes: { 4 Kg. Part (A) : 4 Kg Part (B) } [ ] Mixture should provide a homogeneous yellow colour. [ ] Thinning is not recommended / required. (Solvent-Free Material). [ ] METHOD OF APPLICATION: Can be applied with hand trowel, putty knife, spatula or steel scraper.
Important restrictions
[ ] For minimal wastage, mix estimated quantities which can be used / applied within 30 minutes. [ ] For a second layer coat application, allow a minimum of 6 hours interval. [ ] Sanding can be carried out after a minimum of 24 hours. [ ] GTC Epoxy Putty can be applied over suitably primed/sealed surfaces i.e., Getoxy Clear Sealer (Concrete Surfaces) Getathane Clear Coating (Wooden Surfaces) Getoxy Iron Oxide Epoxy (Steel Surfaces)
Cleaning tools
Uncured Epoxy Putty can be cleaned with GTC099 Thinner immediately after use.
Application conditions
At a temperature ranging 5°C (41°F) to 40°C (104 °F). Relative humidity is below 75%.
Storage and handling
Product must be stored as per local regulations and should be kept in dry well ventilated location far from heat and direct sunlight. Can should be tightly closed after use Mix well before use. Storage temperature range between 5°C (41°F) to 40°C (104 °F).
Safety precautions
The following notes should be considered when using/applying material:- (a) Take precautions to prevent material entering the eyes (goggles should be worn, irrigate the eyes with water when become contaminated and obtain medical care at one). (b) Take precautions to avoid skin contact (gloves should be worn, barrier cream should be used). (c) Ensure that repeated contact of paint with skin is avoided. (d) Provide adequate ventilation. (Face masks must be worn). (e) Keep away from sparks and open flames (for solvent-based materials).
Pack sizes
• 4 kg (Part A) • 4 kg (Part B)