Product description
A two pack Polyamide Cured Epoxy Primer/Sealer coat suitable for application over porous surfaces in both New Construction and Maintenance & Repair Projects.
Special features
[ ] Excellent adhesion and penetration properties. [ ] Provides an excellent key fo subsequent treatment with two pack epoxy systems. [ ] Good abrasion and chemical resistant properties. [ ] Resistant to solvents and industrial detergents. [ ] Suitable for application to areas exposed to continuous splashing with water and subjected to chemical fumes and intermittent spillages of acids.
Where to use
As an internal/external primer and/or finish coat over various surfaces i.e., [ ] concrete [ ] wood [ ] asbestos [ ] bricks [ ] stone [ ] fountains [ ] artificial water falls
Product data
FINISH : GLOSS COLOUR : Clear VOLUME SOLIDS : 58 % PRODUCT WEIGHT : 1 kg/ltr. REC. FILM THICKNESS : Wet : 75 microns per coat (approx. 3 mils) Dry : 35 microns per coat (approx. 1.4 mil) THEO. COVERAGE : 16.5 m2/ltr. Practical coverage primarily depends upon nature of surface profile, method of application and site conditions. MIXING RATIO : Base : Curing Agent 4 : 1 (by volume) POT LIFE : Ambient Temperature 10 °C 25 °C 40 °C 50 °F 77 °F 104 °F No. of Hours 12 hrs. 8 hrs. 4 hrs. FLASH POINT : Base : 32 °C (90 °F) Curing Agent : 23 °C (73 °F) Mixed : 23 °C (73 °F)
Drying times
SUBSTRATE TEMPERATURE | TOUCH DRY | HARD DRY | FULL CURE TIME | OVERCOATING INTERVALS MINIMUM | MAXIMUM 10 °C (50 °F) | 4 hrs. | 36 hrs. | 10 days | 30 hrs. | 7 days 25 °C (77 °F) | 3 hrs. | 24 hrs. | 1 week | 18 hrs. | 7 days 40 °C (104 °F) | 2 hrs. | 18 hrs. | 5 days | 14 hrs. | 7 days
Surface preparation
1. Degrease areas where grease, oil, soil and surface contamination exist in accordance with SSPC-SP1 Solvent Cleaning. (Use GTC002 Thinner). 2. Wire brush/mechanical power tool clean areas where laitance, surface porosity and loosely adhering foreign material exist in accordance with SSPC-SP2 and/or SSPC-SP3 Standards. 3. Surfaces to be coated must be dry, clean and contamination free prior to paint application process.
Where to use
1. Clear Finish: As a two or three coat application; First coat to be thinned down 30% by volume with recommended thinner to act as a primer sealer coat; whereas Second & Third coats to be thinned down up to 20% by volume only. 2. Coloured Finish: As a single priming/sealing coat only, thinned down 20% by volume to act as a primer/sealer and to be overcoated with a selected range of Getoxy material as well as Getathane Recoatable Polyurethane Finishes ... etc.
Mixing and thinning
Material must be properly mixed and is recommended for thinning with GTC099 Thinner. [ ] METHOD OF APPLICATIONS: GTC Getoxy (GES/GEC024) Epoxy Clear Sealer can be applied by Brush, Roller, Conventional and Airless Spray Equipments/Machinery.
Important restrictions
For best results over porous surfaces Brush Applications is recommended as this method helps achieving maximum penetration and adhesion into the substrate.
Cleaning tools
For cleaning tools and equipments use GTC099 Thinner.
Application conditions
At a temperature ranging 5°C (41°F) to 40°C (104 °F). Relative humidity is below 75%.
Storage and handling
Product must be stored as per local regulations and should be kept in dry well ventilated location far from heat and direct sunlight. Can should be tightly closed after use. Mix well before use. Storage temperature range between 5°C (41°F) to 40°C (104 °F).
Standards and approvals
Supportive information is available upon request to establish an assessment to be acquired as with regards to product's compliance with/to a particular authority's queries / specifications. Please consult with GTC Technical Service Dept.
Safety precautions
The following notes should be considered when using/applying painting material:- (a) Take precautions to prevent material entering the eyes (goggles should be worn, irrigate the eyes with water when become contaminated and obtain medical care at once). (b) Take precautions to avoid skin contact (gloves should be worn, barrier cream should be used). (c) Ensure that repeated contact of paint with skin is avoided. (d) Provide adequate ventilation. (Face masks must be worn). (e) Keep away from sparks and open flames (for solvent-based materials).
Pack sizes
White :- [ ] 3.6 Ltr Tins (Base + Curing Agent) [ ] 18 Ltr Tins (Base + Curing Agent)