Product description
A high quality and Quick Drying Gloss Finish Coat based on specially selected Alkyd Resin developed to facilitate and increase production of fast moving objects versus vast/massive production in the Industrial Field.
Special features
☐ Easy to apply and quick drying. ☐ Excellent levelling properties. ☐ High gloss and resistance to yellowing. ☐ Abrasion resistant and provides a tough film. ☐ Resistant to weathering and regular wash down.
Where to use
As a protective and decorative finish coat over a variety of Interior/Exterior variety of substrates i.e. ☐ Structural Steel ☐ Steel Kitchens ☐ Industrial & Agricultural Machinery. ☐ Street Lighting Poles ☐ Electrical Installation - (cable trunking, telephone boxes, cabinets ... etc.) ☐ Can also be successfully applied over Fiberglass Tank Exteriors and Wooden Surfaces. ☐ Suitable for application over Galvanized Steel and Non-Ferrous Metals upon suitable priming.
Product data
FINISH : GLOSS COLOUR : According to GTC NEW GLOSS ENAMEL COLOUR CARD RANGE Including White & Black Special colours are available upon request. VOLUME SOLID : 51 % PRODUCT WEIGHT : 1.15 kg/ltr. Wet : 73 microns per coat (approx. 2.9 mils) Dry : 35 microns per coat (approx. 1.4 mils) REC. FILM THICKNESS : THEO. COVERAGE : 14.5 m²/ltr. Practical coverage primarily depends upon nature of surface profile, method of application and site conditions. FLASH POINT : Above 23 °C (73 °F)
Drying times
SUBSTRATE TEMPERATURE | TOUCH DRY | HARD DRY | OVERCOATING INTERVALS | | | MINIMUM | MAXIMUM 10 °C (50 °F) | 2 hrs. | 16 hrs. | 14 hrs. | IND. 25 °C (77 °F) | 1 hour | 12 hrs. | 10 hrs. | IND. 40 °C (104 °F) | 45 min. | 10 hrs. | 8 hrs. | IND.
Standards and approvals
Supportive information is available upon request to establish an assessment to be acquired as with regards to product's compliance with / to a particular authority's queries / specifications. Please consult with GTC Technical Service Department.
Surface preparation
1. Degrease the metal surface in accordance with SSPC-SP1 Solvent Cleaning to remove grease, oil, and other surface contamination where exist. (Use GTC002 Thinner). 2. Wire Brush/Mechanical Power Tool Clean areas where superficial and/or firmly adhering rust exist in accordance with SSPC-SP2 and/or SSPC-SP3 Standards. 3. Surfaces to be coated must be dry, clean and contamination/rust free prior to paint application process.
Application details
☐ USAGE: Intended for two coat applications over well prepared and suitably primed steel & a variety of other metal and non-metal surfaces.
Mixing and thinning
Material must be properly mixed and is recommended for thinning with GTC011 Quick Drying Thinner as per below table:- APPLICATION METHOD | BRUSH/ ROLLER | CONV. SPRAY | AIRLESS SPRAY Thinning by volume (% Max.) | 10% | 15% | 5%
Cleaning tools
For cleaning tools and equipments use GTC011 Quick Drying Thinner.
Important restrictions
1. Best results can be obtained by using conventional spray method of application. 2. For application over non-ferrous metals and galvanized steel surfaces a selection of GTC peculiar primers should be carried out i.e., a) Getaprime Etching Wash Primer b) GTC Zinc Chromate Primer (Please consult with GTC Technical Service Dept. and refer to individual product data sheets). 3. Avoid exceeding recommended Dry Film Thickness per coat as this tends to detain drying time and causes blistering of paint coating due to solvent entrapment.
Application conditions
At a temperature ranging 5°C (41°F) to 40°C (104 °F). Relative humidity is below 75%.
Storage and handling
Product must be stored as per local regulations and should be kept in dry well ventilated location far from heat and direct sunlight. Packing should be tightly closed after use. Mix well before use. Storage temperature range between 5°C (41°F) to 40°C (104 °F).
Safety precautions
The following notes should be considered when using/applying painting material: (a) Take precautions to prevent material entering the eyes (goggles should be worn, irrigate the eyes with water when become contaminated and obtain medical care at once). (b) Take precautions to avoid skin contact (gloves should be worn, barrier cream should be used). (c) Ensure that repeated contact of product with skin is avoided. (d) Provide adequate ventilation. (Face masks must be worn). (e) Keep away from sparks and open flames (for solvent-based materials).
Pack sizes
☐ Gallon ☐ 18 Ltr. Drum