Product description
A structured rendering based on Acrylic Copolymer reinforced with high quality aggregates, designed to be applied by Trowel to give a characteristic textured finish.
Special features
• Easy trowel application and ready for use. • Excellent alkaline and weather resistant properties. • Water vapour permeable unsaponifiable coat. • Hides minor surface irregularities. • Tough and durable coat with outstanding impact resistance, yet flexible. • Very good adhesion properties.
Where to use
As a decorative and protective Interior / Exterior structured coat over new and old building surfaces i.e., • Interior /exterior concrete and plastered walls. • Gypsum board. • Concrete, GRC blocks. • Wooden Surfaces. • Block works, brick works, stone ... etc.
Product data
FINISH : Textured MATT. COLOUR : WHITE & LIGHT COLOURS. Special colours are available upon request VOLUME SOLIDS : 72 % PRODUCT WEIGHT : 1.75 kg/ltr. FILM THICKNESS : Approx. 0.8 - 1mm . THEO. COVERAGE : Approx. 0.6 m2/ kg. Practical coverage primarily depends upon nature/degree of surface porosity, method of application and site conditions. FLASH POINT : Non-flammable (water-borne product)
Drying times
_____________________________________________________________ Substrate Temperature | Touch Dry | Hard Dry | OVERCOATING INTERVALS | | | MINIMUM | MAXIMUM _____________________________________________________________ 10 °C (50 °F) | 3 hrss | 9 hrss | 38 hrss | IND. 25 °C (77 °F) | 2 hrss | 8 hrss | 24 hrss | IND. 40 °C (104 °F) | 1 hour | 6 hrss | 18 hrss | IND.
Surface preparation
NEW SURFACE : 1. Degrease areas where grease, oil, soil and other surface contamination exist in accordance with SSPC-SP1 Solvent Cleaning . (Use GTC002 Thinner). 2. Wire Brush/Mechanical Power Tool Clean Concrete areas where laitance, surface porosity and loosely adhering foreign material exist in accordance with SSPC-SP2 and/or SSPC-SP3 Standards 3. Surfaces to be coated must be dry, clean and contamination free prior to paint application process. OLD/PREVIOUSLY PAINTED SURFACES: 1. Degrease areas where grease, oil and other surface contamination exist in accordance with SSPC-SP1 Solvent Cleaning. (Use GTC002 Thinner). 2. Remove all blistered, cracked and brittle paint coats off the surface. 3. Coats with inadequate adhesion must be properly scraped-off to a firm edge. 4. Glossy paint coatings must be sanded/roughened to ensure proper intercoat adhesion characteristics with successive paint coatings. 5. Surfaces to be coated must be dry, clean and contamination free prior to paint application process.
Mixing and thinning
Material must be properly mixed before use and thinning is not recommended. • METHOD OF APPLICATION: Intended for a single coat application using Trowel over well prepared, primed and undercoated surfaces as follows :- • RECOMMENDED PRIMER/SEALER: 1. GTC Acrylic Sealer (thinned 50-100% by volume with fresh water). 2. GTC Textured Primer (thinned 25% by volume with fresh water) 3. GTC P.Synthetic Sealer (thinned 25% by volume with GTC002 Thinner).
Important restrictions
Due to severe dust conditions in Kuwait, this product will retain dust and dirt causing discoloured appearance; therefore, in order to overcome the discolouring problem and also to enhance product properties, it is recommended to apply a protective / decorative coat of the following:- A. Getathane Recoatable Polyurethane Gloss or Matt Finish (White or selected colours). B. GTC Acrylic Guard Gloss Finish (White or selective colours) . C. Getashine Acrylic Emulsion Paint (White or selective colours). D. GTC Super Glaze (Clear). E. Getathane Recoatable clear coating (Clear). (Refer to individual data sheet for additional information). • TROWEL APPLICATION: Apply a single coat of E.L. Trowtex Fine with stainless trowel. • E.L. TROWTEX FINE MAY BE SPRAYED.
Application conditions
At a temperature ranging 5°C (41°F) to 40°C (104 °F) . Relative humidity is below 75%.
Storage and handling
Product must be stored as per local regulations and should be kept in dry well ventilated location far from heat and direct sunlight. Can should be tightly closed after use. Mix well before use. Storage temperature range between 5°C (41°F) to 40°C (104 °F).
Safety precautions
The following notes should be considered when using/applying painting material:- (a) Take precautions to prevent material entering the eyes (goggles should be worn, irrigate the eyes with water when become contaminated and obtain medical care at once). (b) Take precautions to avoid skin contact (gloves should be worn, barrier cream should be used. (c) Ensure that repeated contact of paint with skin is avoided. (d) Provide adequate ventilation. (Face masks must be worn). (e) Keep away from sparks and open flames (for solvent-based materials).
Pack sizes
• 25 KG Drum.