A water-borne coating based on modified Acrylic Resin. It is a perfect solution to protect the wall, painted or new, against disfigurement or graffiti with our ruin the wall.
Features
- ☐ Offering a total protection against spray paints, felt-tip pens or similar.
- ☐ Can be easily reapplied on the same surface.
- ☐ It is biodegradable, has a good resistance against atmospheric and chemical agents.
- ☐ Shows an excellent adhesion on different kind of materials.
- ☐ Neither harmful nor toxic for men and environment.
Uses
- As an protective coating for interior/exterior new as well as old surfaces i.e. ☐ All kind of concrete, plaster, terracotta, stones, marble and granite.
Product description
A water-borne coating based on modified Acrylic Resin. It is a perfect solution to protect the wall, painted or new, against disfigurement or graffiti with our ruin the wall.
Special features
☐ Offering a total protection against spray paints, felt-tip pens or similar. ☐ Can be easily reapplied on the same surface. ☐ It is biodegradable, has a good resistance against atmospheric and chemical agents. ☐ Shows an excellent adhesion on different kind of materials. ☐ Neither harmful nor toxic for men and environment.
Where to use
As an protective coating for interior/exterior new as well as old surfaces i.e. ☐ All kind of concrete, plaster, terracotta, stones, marble and granite.
Product data
FINISH : MATT. COLOUR : CLEAR PRODUCT WEIGHT : 1.1 Kg/Ltr. THEO. COVERAGE : 8 m²/ltr.for 3 coats Practical coverage primarily depends upon nature/degree of surface porosity, method of application and site conditions. FLASH POINT : Non-flammable (water-borne product)
Drying times
SUBSTRATE TEMPERATURE | TOUCH DRY | HARD DRY | OVERCOATING INTERVALS MINIMUM | MAXIMUM 10 °C (50 °F) | 3 hrs. | 7 hrs. | 7 hrs. | IND. 25 °C (77 °F) | 2 hrs. | 5 hrs. | 5 hrs. | IND. 40 °C (104 °F) | 1 hour | 4 hrs. | 4 hrs. | IND.
Surface preparation
Remove all dust, dirt, oil and grease contamination, loose particles, laitance and old paint...etc, the surface must be smooth and dry.
Application details
☐ USAGE: Intended for a 2-3 coats over well prepared surfaces. with . crossed layers and with at least 5-6 hours between 2 consecutive coats. ☐ METHOD OF APPLICATION: DL Antigraffiti coating can be applied by Brush , Roller or conventional a spray.
Cleaning tools
For cleaning tools and equipment use fresh water only.
Application conditions
At a temperature ranging 5°C (41°F) to 40°C (104 °F). Relative humidity is below 75%.
Storage and handling
Product must be stored as per local regulations and should be kept in dry well ventilated location far from heat and direct sunlight. Can should be tightly closed after use. Mix well before use. Storage temperature range between 5°C (41°F) to 40°C (104 °F).
Standards and approvals
Supportive information is available upon request to establish product compliance with a particular specification. Please consult with GTC Technical Service Dept.
Safety precautions
The following notes should be considered when using/applying painting material:- (a) Take precautions to prevent material entering the eyes (goggles should be worn, irrigate the eyes with water when become contaminated and obtain medical care at once). (b) Take precautions to avoid skin contact (gloves should be worn, barrier cream should be used). (c) Ensure that repeated contact of paint with skin is avoided. (d) Provide adequate ventilation. (Face masks must be worn). (e) Keep away from sparks and open flames (for solvent-based materials).
Pack sizes
2.5 ltr. Can : 1 ltr. Plastic Can.